Archive for the ‘ Tutorials ’ Category

WIP Land speeder

Got a vacation coming up and decided to start a new project. The land speeder comes with a few different options and not to limit my self by gluing all the parts together I decided to magnetize the different part. After some searching on Google I found a really good guide over at Talonstrike.

I made a few alteration from the original guide.

land_speeder_front_gun_wip I started with drilling a small hole on the gun mount and then dry fitted the guns, drilled a hole threw the hole I just did into the gun.

Then I used a 3mm drill to make the hole large enough for the magnets. I then glued the a 3mm magnet to the gun mount.

When it was dry I attached a second magnet to the magnet I glued on the mount. Put some glue into the hole on the gun and fitted it to the magnets, then turned it carefully to detach it.

land_speeder_gunner_wipThe gunners was a bit more tricky, I first drilled a small hole threw the weapon grip. Dry fitted the guns and drilled a hole threw the grip to the weapon. Then used the 3mm drill to widen the holes.

I then glued the magnets into place, now comes the tricky part. To get the arms attached to the torso correctly. I did this by attaching one of the guns to the arms. Pinned the torso to the seat and dry fitted everything else. Then applied glue to where the arms fit on the torso and then put the gun with the arms in place carefully to attach the arms to the torso.

land_speeder_guns_wipThe sides followed Talonstrike guide on how to magnetize a land speeder. Basically  build up an inner wall for the doors, Fit and glue the magnets on the inside of the wall.  Make sure to dry fit them first to get a good position. I used 5mm magnets for this.

Remove the hinges and the inner part of the missile launcher doors.

land_speeder_side_gun_mount_wip

When you have glued the magnets on the inside of the built up wall, put another magnet on the outside, it will align up automatically with the inner magnet. Put some glue on the door and on the outside magnet, fit the door and wait for the glue to dry. Remove the door and magnet should have stuck to the door.

You can now strengthen the hold of the magnets by adding some green stuff around them.

land_speeder_wip

We now have a fully customizable land speeder with the weapons of choice.

The torsos and the top part of the land speeded is not glued and will be painted before I glue them in place.

Tactical marine step by step

This tutorial start from after the base colouring and washing I did earlier in Paint and spray post.

Armour

tactical_marine_step_11

1: Apply a highlight of mordian blue on the base coated marine. Make sure to leave some of the base coat in the crevasses and darker areas (left picture).

2: Apply a second highlight of ultramarines blue, during this step I tried to do some feathering (right picture). Using two brushes in the same hand, one with the  colour and the other one damped with little water and after applying the colour I switched brush and then smeared out the edges of the painted area to even out the transition.

3: Paint all details that are not suppose to be blue with chaos black in preparation for the next step.

Lenses

tactical_marine_detail_eyes

1: Paint the whole lense with mechrite red.

2: Paint the  lower inner side of the lens with blood red.

3: Hightlight the bottom of the blood red area with blazing orange.

4: Paint a small skull white dot on the outer upper side of the lens

5: Paint a thin line around the edges of the lens with baal red. This will create a bit of contrast to the armour.

Gold details

tactical_marine_chest

1: Paint the shoulder frames and chest plate with shining gold (first picture).

2: Wash the gold details with devlan mud (second picture).

3: Highlight the gold with burnished gold (third picture)

4: Paint a touch of mithril silver over the out most part of the chest plate (fourth picture).

Purity seal and parchment

1: Paint the seal with mechrite red

2: Wash the seal with baal red

3: Highlight the raised areas with blood red

4: Highlight  the most raised areas with blazing orange

5: Paint the parchment with tausept ochre

6: Highlight the parchment with bleached bone

7: Wash the parchment with gyphonne sepia

8: Paint some thine line on the parchment with badab black

Metal details

tactical_marine_gun

1: Paint all the metal details with boltgun metal.

2: Wash the boltgun metal with badab black.

3: Highlight the raised metal areas with chainmail silver.

Black areas (Gun casing)

1: Highlight the raised black areas with adeptus battlegrey.

2: Hightlight the most raised areas of the adeptus battlegrey with fortress grey

If you need to even out some of the highlight I find it very effective to use the badab black wash to tone them down.

Armour step 2

tactical_marine_step_21

1: Highlight the edges around the armour with a mix of ultramarines blue and skull white. This will give the character more contrast.

I didn’t measure this mix exactly but start with adding the ultramarines blue to a empty pot and then add white until you get a good light blue colour, then simply add water until it get the consistency of skimmed milk.

On my first tactical marine I used skull white for this step making it look a bit like a cartoon character. I have gone back and painted over the white with this mix.

Assembly

tactical_marine_done

1: Glue the backpack and the gun in place.

2: Secure the model firmly with pining it to the base and some plastic glue.

3: Done!!

Tactical squad bases

I have done the bases for the rest of my tactical marines. I am trying to make it look like an urban warfare zone, where fighting has gone on for generations, a lot of broken concrete and debris laying around.

tactical_marines_base_1

The first step in creating the bases was to break apart a normal CD jewel case, I did this by cutting random lines in the case and then breaking them of by hand. I then used my trusty glue gun and pick two to three bigger pieces and glued them to the base.

I also added some brass wire on some of the bases to look like reinforcement beams.

tactical_marines_base_2

Second step is to add some debris, I used the slate that I got from the 40k basing kit but any small rocks or sand will work. I glued them to the base with normal PVA glue.

tactical_marines_base_3

Step three is to start painting, and to start painting you need to spray it with a black base coat.

tactical_marines_base_4

Step four is to dry brush all the bases with adeptus battle grey, the concrete was painted normally with the same colour.

tactical_marines_base_5

Step five is to dry brush a layer of codex grey to the bases. Make sure to cover the corners of the concrete.

tactical_marines_base_6

Final step is dry brush the slate or sand with fortress grey, highlight the corners of the concrete. I also added some weathered numbering on two of the bases.

tactical_marines_base_7

The only thing left now is to do some touch up on the base and then pin the marines to the base.

Wear and tear effect

The drop pod has a lot of flat areas and a great way to lift the model is to apply wear and tear to the hull, which is the choice many painters have done with their drop pods and this is how I did my wear and tear effects.

wear_and_tear

First step is to apply the base colour of the tears at some selected areas,  Around corners are a good choice and where the doors might hit the ground are also good places. I used adeptus battlegrey to paint the first layer of wear and tear.

The second step is to fill in the areas which have been painted with boltgun metal. Make sure not to fill in all of the area and let some of the grey still be visible.

The third step is to highlight and darken the tear effect, I did this by applying chainmail to the raised areas and a very thin line of badab black to the lower and right side of the tear.