Posts Tagged ‘ Ultramarines

Tactical marine step by step

This tutorial start from after the base colouring and washing I did earlier in Paint and spray post.

Armour

tactical_marine_step_11

1: Apply a highlight of mordian blue on the base coated marine. Make sure to leave some of the base coat in the crevasses and darker areas (left picture).

2: Apply a second highlight of ultramarines blue, during this step I tried to do some feathering (right picture). Using two brushes in the same hand, one with the  colour and the other one damped with little water and after applying the colour I switched brush and then smeared out the edges of the painted area to even out the transition.

3: Paint all details that are not suppose to be blue with chaos black in preparation for the next step.

Lenses

tactical_marine_detail_eyes

1: Paint the whole lense with mechrite red.

2: Paint the  lower inner side of the lens with blood red.

3: Hightlight the bottom of the blood red area with blazing orange.

4: Paint a small skull white dot on the outer upper side of the lens

5: Paint a thin line around the edges of the lens with baal red. This will create a bit of contrast to the armour.

Gold details

tactical_marine_chest

1: Paint the shoulder frames and chest plate with shining gold (first picture).

2: Wash the gold details with devlan mud (second picture).

3: Highlight the gold with burnished gold (third picture)

4: Paint a touch of mithril silver over the out most part of the chest plate (fourth picture).

Purity seal and parchment

1: Paint the seal with mechrite red

2: Wash the seal with baal red

3: Highlight the raised areas with blood red

4: Highlight  the most raised areas with blazing orange

5: Paint the parchment with tausept ochre

6: Highlight the parchment with bleached bone

7: Wash the parchment with gyphonne sepia

8: Paint some thine line on the parchment with badab black

Metal details

tactical_marine_gun

1: Paint all the metal details with boltgun metal.

2: Wash the boltgun metal with badab black.

3: Highlight the raised metal areas with chainmail silver.

Black areas (Gun casing)

1: Highlight the raised black areas with adeptus battlegrey.

2: Hightlight the most raised areas of the adeptus battlegrey with fortress grey

If you need to even out some of the highlight I find it very effective to use the badab black wash to tone them down.

Armour step 2

tactical_marine_step_21

1: Highlight the edges around the armour with a mix of ultramarines blue and skull white. This will give the character more contrast.

I didn’t measure this mix exactly but start with adding the ultramarines blue to a empty pot and then add white until you get a good light blue colour, then simply add water until it get the consistency of skimmed milk.

On my first tactical marine I used skull white for this step making it look a bit like a cartoon character. I have gone back and painted over the white with this mix.

Assembly

tactical_marine_done

1: Glue the backpack and the gun in place.

2: Secure the model firmly with pining it to the base and some plastic glue.

3: Done!!

Ultramarines drop pod

I finished my drop pod. It took a lot more time to paint then I first had thought, but I am happy with the result.

The only different thing I would do if I paint another one, is that I will paint it before I assemble it.

ultramarines_drop_pod_close

I have added the Ultramarines logo and the number one decals on the tail wings, this to show that the drop pod belongs to my first tactical squad which will also get the number one painted on their right shoulder.

ultramarines_drop_pod_open

Wear and tear effect

The drop pod has a lot of flat areas and a great way to lift the model is to apply wear and tear to the hull, which is the choice many painters have done with their drop pods and this is how I did my wear and tear effects.

wear_and_tear

First step is to apply the base colour of the tears at some selected areas,  Around corners are a good choice and where the doors might hit the ground are also good places. I used adeptus battlegrey to paint the first layer of wear and tear.

The second step is to fill in the areas which have been painted with boltgun metal. Make sure not to fill in all of the area and let some of the grey still be visible.

The third step is to highlight and darken the tear effect, I did this by applying chainmail to the raised areas and a very thin line of badab black to the lower and right side of the tear.

My first ultramarine

I finished my first ultramarine this weekend and I most say that I surprised my self this time, Very happy with the result.

tactical_first_marine_front

tactical_first_marine_back

I will do a detail step by step post when I start with the other marines from the tactical squad. But the next thing will be to finish the drop pod. I will then paint the tactical squad four at a time and the veteran sergeant separately.

Paint and spray

I bought a new toy, a spray gun and decided to try it on my tactical squad from the assault on black reach set.

I am very impressed by how simple it was and a very good time saver, I wish I had this when I started the drop pod.

Now to start with the tactical squad I started to spray them with a standard chaos black as I normally do with my painting.

tactical_squad_1

I then applied a single coat of mordian blue mixed with water with the spray gun, it was a bit messy at start but when I got a hang of the spray gun it went a lot smoother.

tactical_squad_2

The second layer I applied with the spray gun was a asurmen blue wash. This wash sinks nicely into the crevasse and created a bit of contrast.

tactical_squad_3

Next is a close up on the picture above, where you can see how the wash really gets into crevasses and corners.

tactical_squad_4

This method of painting is a bit more expensive, since you need to buy propellent for the gun and you waste a bit more of paint but it is all worth it.

Next step is to apply a new layer of mordian blue to the raised areas and lighten the characters.

Then do two layers of highlighting, first one with ultramarines blue and then a layer of ice blue and ultramarines blue mix.

After that I need to fix all the details that now is blue to get correct colour but that is another post.